Episode 77 – The ULTIMATE Finish , Sled? What Sled!, MDF For Shop Furniture? & MUCH More!

Support us on Patreon: https://www.patreon.com/woodshoplife
 
Sean
1)Hi guys
I'm in the market for a miter gauge for my table saw and really like the look of the Incra Miter 5000 but the cost over here in Australia is a bit on the high side ($700 plus postage). Ive started looking around at different manufacturers etc and the usual YouTube searching and I notice a lot of users using a miter gauge only as opposed to a sled with miter type options.
Would you use a miter gauge only as opposed to a sled configuration. Thanks for the great podcast Geoff
2) I would like to make a assembly table top with dog holes just like the MFT basic. I already have an MFT table. Would it be possible to use my existing MFT table top as a template on a larger piece of 3/4 MDF? I was thinking of clamping it down somehow and pre drilling some holes and using my festool plunge router with a flush trim bit. Would this work and how would you do it with what kind of router bit? I see a lot of jigs made or bought online for this but if I already have a MFT table why not use it as a template - Anythony
 
Guy
1) Long-time podcast listener, thanks for the great content and helpful advice for woodworkers of all skill levels! I'm a few years into woodworking and have a 12 x 15 shop in my basement. No windows in the basement and my workshop is in the climate-controlled utility room with the finished basement just outside the workshop door. I make a variety of things such as boxes, crosses, shelves, trays, etc out of hardwoods, primarily walnut and curly maple. So far, my go-to finish has been a few coats of Shellac (Zinsser Sealcoat) finished with a coat of satin Arm-R-Seal. This finishing process can be a bit tedious, especially when making crosses and boxes that have lots of small crevices.  I'd love to settle on a finish that checks the following boxes:
- Easy to apply
- Isn't overly smelly, given my workshop location and lack of outside ventilation
- Accentuates the beauty of the wood (e.g. highlights the figure in the curly maple, richness of color of the walnut).
- Doesn't involve pre-finishing, if possible, as I'm lazy and often have some sanding and clean-up work to do after assembly.
- Is quick from start to finish, as my workshop time is limited with 3 young kids and I want to spend as much of the shop time as possible making sawdust, not applying finish.
- Easy to clean up. For example, I'd love to avoid spending 30 minutes cleaning a spray gun after using it. Also, I don't have a ton of space due to my Sawstop PCS 36" saw, router table, planer, drill press, etc.
Should I keep with Shellac and Arm-R-Seal, or should I look at a spray option? And if a spray option, should I do an actual sprayer or buy rattle cans of finish? I'm open to recommendations. Thanks! Brian
2) Being 69 years old now, I find my reflexes, muscle control, eyesight etc. aren't quite as good as they used to be. Would it be, in your opinion, foolish to go to a SawStop table saw for the increased safety, when my Powermatic PM 2000 works fine. I realize there are other sources of hazards in the shop, but reducing one at the table saw is being considered. Thanks for the great podcast! Tim in North Carolina
 
Huy
1)Hi Guy, Huy, and Sean, love the podcast, I learn so much every episode. After only a year of woodworking, I've decided it's time to get my shop better organized. I'm going to start making a lumber cart, clamp racks, flip top tool stand, various storage cabinets, assembly table, etc. Most designs for these kinds of things call for plywood. But with plywood prices through the roof, I don't want to spend a ton of money on each thing. MDF prices are still high but seem a bit more reasonable. How can I determine when MDF can be substituted for plywood? And do you have any other tips for how to make shop furniture on the cheap with today's prices? Thanks, Matthew
2) Hey Guys, love your podcast; it’s one of the few woodworking podcasts out there that actually pushed me to be a better woodworker. Keep it coming. My question is this: I’m considering purchasing a dust extractor. I currently don’t any any Festool products, but I am considering the new Festool C15 dust extractor. (My budget doesn’t allow for the high prices of the other units with Bluetooth and since I dont own any other Festool products, I don’t see a reason to have any of the other units, but maybe someday). My current set up for my orbital sander, biscuit jointer, etc is a 4 gallon 5hp Dewalt shop vac with 90 CFM. I also have the vac and tools plugged into an I-socket auto switch which allows the vac to automatically turn on/off when I run my tools. I find that this set up does really well. With a price tag at $350, do you think it’s worth it in my situation to upgrade to a C15? What additional benefits do I gain from it that I don’t already have?

- Scott