Episode 69 – Dream Bandsaw?, Three Phase, Tunes in The Shop, & MUCH More!

Support us on Patreon: https://www.patreon.com/woodshoplife
 
Sean
1) Hey guys, I became a patron supporter a couple months ago and I really love the format of the podcast. I am a beginner woodworker who is in the process of acquiring more tools. I would like to start to resaw my own lumber from rough sawn. I was hoping to get your advice on what is the best bandsaw you all would recommend. If money was no object what would you recommend? Again, my main objective is to resawn Lumber and the number one challenge I’m facing in picking a machine is they are not on display at any of the usual stores, Woodcraft or Rockler. I appreciate your response in advance. Juan from Boston
2) Hey guys! Digging the podcast, keep up the good work.
I have a question and curious how you guys would approach fixing tear out on a table top?
I’ve got a ambrosia maple top I just glued up. And noticed a nice 1/2” x 1/2” wide chunk that’s  about a 1/16 to 1/8” deep right in the middle of the top. How would you fix it? Also you can’t flip the top, there another mark/divot that’s worse on the bottom side.
Would you use a decorative inlay/ bow tie? Or try to hide it?
Details: Top is 1.75” thick, I know a little heavy but gets a large chamfer on the underside. Overall it will be 40” wide by 7ft long.
And I don’t have access to a wide belt sander.
Thanks, Jesse
 
Huy
1) Hey guys! Great show! I have been having problems with raising and lowering the height of my table saw blade. I have a Grizzly 1023RLW. It is new from Grizzly, and have had it for about 6 months. My question is, what do you guys use as a lubricant for the moving parts? I cleaned everything good, and used grease. Like packing bearings grease. It works great for about a week, and then gets all packed with sawdust. Is there a better way? Thanks for the show, it has been a real help. Keep it up! Marc
2) Good day Sean, Huy and Guy.  Thank you for the podcast.  It is an excellent resource.  I prefer the french pronunciation of Guy, so in my world Huy and Guy rhyme which greatly increases my enjoyment of the podcast. 
I recently got a 20" bandsaw for free.  It has a 3 phase motor right now.  Is there a compelling reason to purchase a phase convertor as opposed to a new motor?  They are in the same ballpark in terms of price--the motor being a bit more expensive.   It may be more difficult to find the motor with the proper mounting brackets and etc. but I would guess I can find it.  Is there a performance based reason to select one or the other?  (Huy should great insight on this as a rocket scientist which is a close cousin to an electrical engineer, right?)
Thank you for any insight you may have. Darrick
 
Guy
1) So a bit of non woodworking question for you - I need some new music to listen to in the shop. What’s on your playlists right now?
For the record, I don’t listen to music while I’m using anything with a blade or cutter, it’s too distracting. only when I’m sanding and finishing. Just sayin’.
Thanks, Mark B
2) My shop is being constructed and I’m about to face the electrical decisions.  One decision I’m stuck on and could use some other input on is about the tools in the middle of the shop. I don’t like cords running across the floor to trip on, so I’m considering putting some outlets in the ceiling and having the cords come down with the dust collection run.  I’ll need 240 and 120 for the center tools.  Does this sound like a good idea?  Should I try to get something in floor instead?  This would add cost, but then think I would need to consider adding dust collection pipe as well to free up my head space.  My ceilings will be vaulted, so that brings another complication.  Just looking for thoughts from seasoned woodworkers.
Brian